Epson
TM-m10 User’s Manual

Epson

TM-m10 User’s Manual

Before Using the Printer

Important Safety InformationProduct Information PageChecking Items Included with the Printer

Part Names

Part Names

Setup

Checking/Changing the Installation DirectionConnecting CablesConnecting Smart DevicesAttaching the Power Switch Cover

Basic Operations

Turning the Power On/OffRemoving/Attaching the Covers (Rear and Bottom)Feeding the Roll PaperInstalling or Replacing the Roll Paper

Cleaning

Cleaning the Printer CaseCleaning the Thermal Head and the Platen Roller

Troubleshooting

Cannot PrintLED Panel Lights are On/Flashing/OffWhen the Roll Paper JamsThe Roll Paper Cover Does not Open

Appendix

SpecificationsRestriction of UseCAUTIONSTrademarks

Top > Setup > Connecting Cables

Connecting Cables

Connect the AC adapter and the interface cable to the connectors at the bottom of the printer.

WARNING:

Be sure to use the specified AC adapter [AC Adapter,C1 (Model: M235B)] only.

  1. Remove the cover if it is attached.
    Removing the covers

  2. Connect the AC adapter and the interface cable to the connectors at the bottom of the printer.

  3. The available interfaces vary by the printer model.

    Note:
    • When using the optional Wireless LAN unit, connect the unit to the USB connector.

    • When routing the USB cable through the hole in the center of the cover, attach the locking wire saddle as shown in the illustration to secure the USB cable and prevent it from disconnecting accidentally. This is unnecessary when routing the USB cable through the holes in the corners.

  4. Reattach the cover.
    Attaching the covers

  5. Connect the interface cable to the device.

  6. Connect the AC cable plug to a power outlet.

  7. WARNING:
    • Never insert the AC cable plug into a socket that does not meet the input voltage of the AC adapter. Doing so may result in damage to the printer.

    • Should a fault ever occur, immediately turn off the power to the printer and unplug the AC cable from the socket.

Before Using the Printer

Important Safety InformationProduct Information PageChecking Items Included with the Printer

Part Names

Part Names

Setup

Checking/Changing the Installation DirectionConnecting CablesConnecting Smart DevicesAttaching the Power Switch Cover

Basic Operations

Turning the Power On/OffRemoving/Attaching the Covers (Rear and Bottom)Feeding the Roll PaperInstalling or Replacing the Roll Paper

Cleaning

Cleaning the Printer CaseCleaning the Thermal Head and the Platen Roller

Troubleshooting

Cannot PrintLED Panel Lights are On/Flashing/OffWhen the Roll Paper JamsThe Roll Paper Cover Does not Open

Appendix

SpecificationsRestriction of UseCAUTIONSTrademarks

Top > Setup > Connecting Cables

Connecting Cables

Connect the AC adapter and the interface cable to the connectors at the bottom of the printer.

WARNING:

Be sure to use the specified AC adapter [AC Adapter,C1 (Model: M235B)] only.

  1. Remove the cover if it is attached.
    Removing the covers

  2. Connect the AC adapter and the interface cable to the connectors at the bottom of the printer.

  3. The available interfaces vary by the printer model.

    Note:
    • When using the optional Wireless LAN unit, connect the unit to the USB connector.

    • When routing the USB cable through the hole in the center of the cover, attach the locking wire saddle as shown in the illustration to secure the USB cable and prevent it from disconnecting accidentally. This is unnecessary when routing the USB cable through the holes in the corners.

  4. Reattach the cover.
    Attaching the covers

  5. Connect the interface cable to the device.

  6. Connect the AC cable plug to a power outlet.

  7. WARNING:
    • Never insert the AC cable plug into a socket that does not meet the input voltage of the AC adapter. Doing so may result in damage to the printer.

    • Should a fault ever occur, immediately turn off the power to the printer and unplug the AC cable from the socket.

©Seiko Epson Corporation 2015-2019. All rights reserved. (M00092007 EN)